How to clean a truck with a pressure washer, you will need a pressure…

 

How to clean a work truck with a pressure washer, you will need a Water Cannon pressure washer with appropriate attachments, a mild detergent, and possibly some additional tools such as a brush or rotating nozzle. Here are the general steps to follow:

1. Park the work truck in a shaded area, out of direct sunlight, to prevent the cleaning solution from drying too quickly.
2. Begin by rinsing the entire surface of the truck with a low pressure spray to remove loose dirt and debris.
3. Mix a mild detergent with water in a bucket, following the manufacturer's instructions.
4. Using the soap injector with the low pressure spray 65 degree (black) nozzle, apply the detergent solution to the truck, working from the top down. Be sure to pay special attention to any areas that are particularly dirty or affected by road film.
5. Allow the detergent to sit on the truck for a few minutes, as per the instruction of detergent usage.
6. Using a high pressure spray and a wide fan nozzle 25 (green) or 40 (white) degree most popular, power wash the truck to remove the detergent and dirt.
7. Rinse the work truck thoroughly with high pressure clean water to remove any remaining detergent or dirt. Some stubborn road film may require a follow up cleaning with soft brush 

                  8. Dry the truck with a clean microfiber towel or chamois to prevent water spots.

Note: Make sure the nozzle of pressure washer is not too close to the vehicle, this might cause paint damage It is always better to test pressure setting in inconspicuous area before starting the process.

Watercannon.com has an entire category dedicated to truck and car wash applications.  

Phone: 833.400.0774 

Cleaning a restaurant exhaust hood using a pressure washer requires…

Cleaning a restaurant exhaust hood using a Water Cannon hot water pressure washer requires proper safety measures and the use of appropriate cleaning products and techniques. Here is a general guide on how to clean a restaurant exhaust hood using a pressure washer:

1. Turn off the exhaust fan and power to the hood and surrounding outlets.
2. Put on personal protective equipment, including eye and ear protection, a respirator mask, and slip-resistant footwear.
3. Remove any loose debris from the hood, such as grease and food particles, using a scraper or other appropriate tool.
4. Apply a degreaser to the hood surface and allow it to sit for the manufacturer's recommended time to loosen and dissolve the grease.
5. Rinse the hood surface with a hot water Water Cannon pressure washer, set to a low-pressure setting, to remove the degreaser and loosen any remaining grease and debris.
6. Use a hot water duty pressure washer nozzle with a 0-degree tip or a surface cleaner attachment to clean the hood surface thoroughly.
7. Rinse the hood surface with a green 25 degree nozzle to remove any remaining debris and residual degreaser.
8. Inspect the hood and filters to ensure they are completely cleaned, if not continue to wash using the hot water setting of 190 degree F.
9. Repeat the process, if necessary.
10. Turn the exhaust fan and power back on and check the hood and filters to ensure they are properly installed.
11. Check with local and state fire codes, most of them require hood cleaning service to be performed by certified hood cleaning companies.

It's always recommended to use a certified hood cleaning professional or have a professional maintenance team to handle the exhaust hood cleaning as it is critical for safety and also to avoid fire hazards.

Phone: 833.400.0774
 

Concrete manufacturing

 

A concrete manufacturing company can use a Water Cannon pressure washer in a variety of ways, including:

1. Cleaning the surface of concrete molds before pouring new concrete.
2. Removing hardened concrete residue from mixers, trucks, and other equipment.
3. Cleaning the surface of freshly poured concrete to remove any surface imperfections.
4. Cleaning finished concrete surfaces, such as sidewalks and floors, to remove dirt and stains.
5. Removing graffiti or paint from concrete surfaces.
6. Cleaning machinery and heavy equipment in the production area, especially in hard-to-reach areas.
7. Preparing surfaces for painting or coating.
8. Cleaning epoxy and polyurethane coating from the surface before reapplication
9. Cleaning and degreasing the oil and grease stain in the manufacturing area
10. Removing rust and corrosion from the steel reinforcement in the fresh concrete

It is important to use the appropriate pressure setting, nozzle, and detergent for the task at hand, to prevent damage to the concrete or equipment. Also, proper safety measures should always be taken, such as wearing eye and ear protection and slip-resistant footwear.

Phone 833.400.0774 

Easy bolt-on axial series pumps come with a special formulated synthetic pump oil that contains anti-wear

 

3200 PSI Axial Pump 

100% Brass Head.

Multiple features like thermal relief valve, 

Soap, chemical injector included

at a new unique competitive $

3400RPM - 3200PSI - 2.4GPM

833.400.0774

Is rebuilding a commercial pressure washer difficult?

Rebuilding a commercial pressure washer can be a complex task that requires a certain level of technical knowledge and skill.

 Depending on the specific make and model of the pressure washer, as well as the extent of the repairs needed, rebuilding the machine can be a relatively simple process or a more challenging one.

If the pressure washer is relatively new and only requires simple repairs, such as replacing a worn out pump or nozzle, then rebuilding it may be relatively straightforward. In this case, it may be possible to do the repairs yourself, provided you have the necessary tools and experience.

However, if the pressure washer is older or requires more extensive repairs, such as replacing the heating elements or overhauling the pump, then rebuilding it can be more difficult. In this case, it may be best to hire a professional technician with experience in rebuilding commercial pressure washers.

It's also important to consider the cost of rebuilding a commercial pressure washer. So it's important to weigh the cost and benefits of rebuilding a pressure washer before proceeding.
In summary, rebuilding a commercial pressure washer can be difficult, depending on the machine's make and model, the extent of the repairs needed, and the tools and expertise you have. It is important to consider the cost and benefits of rebuilding a pressure washer before proceeding.

Please check out Water Cannon’s vast selection of replacement pump packages. 

Water Cannon provides free phone technical support. 
free phone technical support. 800.333.9274

How to maintain a soap injector on a pressure washer

 

To maintain a soap injection on a pressure washer, follow these steps:

1. Make sure the pressure washer is turned off or unplugged before performing any maintenance.
2. Locate the soap injection system, which is typically found near the outlet of the high pressure pump.
3. Remove the chemical intake hose and filter to ensure they are free of obstruction or dried soap residue. 
4. Inspect the nozzle or injector for any clogs or blockages. If you find any, use a small brush or needle to clear them out.
5. Check the hoses and connections for any leaks or damage. If any are found, replace them as necessary.
6. Turn on the pressure washer and test the soap injection system using the large orifice black soap nozzle to make sure it is working properly.
7. Repeat these steps on a regular basis to ensure that the soap injection system is always in good working order. 

It's also important to note that you should always use the correct type of soap for your pressure washer, as using an incorrect soap can damage the machine or make it less effective.

How to maintain a pressure washer hose

There are several ways to maintain a pressure washer hose and extend its life:

1. Store the hose properly: When not in use, store the hose in a cool, dry place out of direct sunlight to prevent it from cracking or becoming brittle.
2. Avoid kinking: Kinking the hose can cause damage to the inner lining, so be careful not to kink the hose when using it or when storing it.
3. Use a hose protector: A hose protector can help protect the hose from damage caused by dragging it across rough surfaces or running over it with heavy equipment.
4. Clean the hose: After each use, flush the hose with clean water to remove any dirt or debris that may have accumulated inside.
5. Inspect the hose regularly: Regularly inspect the hose for signs of wear and tear, such as cuts, abrasions, or leaks. If you notice any damage, replace the hose immediately to prevent further damage.
6. Avoid high temperature: Keep the hose away from high temperatures, it can cause the hose material to degrade, or even melting. Also, be sure to use the pressure washer in the appropriate range of temperatures to avoid these issues.
7. Avoid over pressurizing: Using an overly high pressure or using a hose that isn't rated for the pressure being used can damage the hose. Follow the manufacturer's recommendations for the maximum pressure and flow rate.

By taking these steps, you can help extend the life of your pressure washer hose and ensure that it continues to function properly. Shop www.watercannon.com for a full range of pressure washer hose assembly options.  

 Hoses: 3000PSI - 3900PSI - 4000PSI - 6000PSI - 6100PSI
Steam Cleaning Hoses - Hoses on Sale - Long Length